fabricademy2017:students:output [Textile Academy]

Link to this comparison view

--- fabricademy2017:students:output [2018/03/26 02:30]
ayseesindurmaz
+++ fabricademy2017:students:output [2018/03/27 00:14]
ayseesindurmaz
@@ Line 7: / Line 7: @@
 After many research on the design of my garment, when ı decided to final structure ı started working inflatables.
-{{:fabricademy2017:students:ayseesindurmaz:final_project:koy_benı_de_sıteye.jpg?nolink&872x369}}
+{{:fabricademy2017:students:ayseesindurmaz:final_project:koy_benı_de_sıteye.jpg?nolink&872x369|koy_benı_de_sıteye.jpg}}
 ı wanna make a system with inflatables. My input is working under stress. İn case of stress, the wearable will be inflated.
@@ Line 15: / Line 15: @@
 ===== The component list that I used for output. =====
-^component ^quantity ^Datasheet |
+^component ^quantity ^Datasheet/website |
-|6V small dc motor |2 |  |
+|6V small dc motor |2 |https://www.amazon.de/Luftpumpe-DAYPOWER-LP15-06-6V-430mA/dp/B074M9JML9 |
-|1N4001 diode |2 |  |
+|1N4001 diode |2 |http://www.onsemi.com/pub/Collateral/1N4001-D.PDF |
 |10k Ω Resistor |2 |  |
-|mosfet |2 |https://www.infineon.com/dgdl/irf540n.pdf?fileId=5546d462533600a4015355e396cb199f |
+|mosfet |2 |[[https://www.infineon.com/dgdl/irf540n.pdf?fileId=5546d462533600a4015355e396cb199f|https://www.infineon.com/dgdl/irf540n.pdf?fileId=5546d462533600a4015355e396cb199f]] |
 |Jump wire |24 |  |
-|Arduino uno |1 |  |
+|Arduino uno |1 |https://www.farnell.com/datasheets/1682209.pdf |
-{{:fabricademy2017:students:ayseesindurmaz:final_project:img_8955.jpg?nolink&600x800}}
+{{:fabricademy2017:students:ayseesindurmaz:final_project:img_8955.jpg?nolink&600x800|img_8955.jpg}}
 Arduino code;
-| \\ const int analogInPin = A0;  // Analog input pin that the Galvanic skin sensor is attached to \\  \\ const int analogOutPin = 3; // Analog output pin that the First DC Motor is attached to \\  \\ const int analogOutPinVac = 5; // Analog output pin that the Second DC motor to \\  \\ int sensorValue = 0;        // value read from the pot \\ int outputValue = 0;        // value output to the PWM (analog out) \\  \\ void setup() { \\ // initialize serial communications at 9600 bps: \\ Serial.begin(9600); \\ } \\  \\ void loop() { \\ // read the analog in value: \\ sensorValue = analogRead(analogInPin); \\ // map it to the range of the analog out: \\ outputValue = map(sensorValue, 0,400, 0, 255); \\ // change the analog out value: \\ analogWrite(analogOutPin, outputValue); \\  \\ // print the results to the Serial Monitor: \\ Serial.print("sensor = "); \\ Serial.print(sensorValue); \\ Serial.print("\t output = "); \\ Serial.println(outputValue); \\  \\ // wait 2 milliseconds before the next loop for the analog-to-digital \\ // converter to settle after the last reading: \\ delay(2); \\ } \\  |
+| \\ const int analogInPin = A0; // Analog input pin that the Galvanic skin sensor is attached to \\   \\ const int analogOutPin = 3;//Analog output pin that the First DC Motor is attached to \\  \\ const int analogOutPinVac = 5; // Analog output pin that the Second DC motor to \\  \\ int sensorValue = 0;//value read from the pot \\ int outputValue = 0; // value output to the PWM (analog out) \\  \\ void setup() {// \\ initialize serial communications at 9600 bps: \\ Serial.begin(9600); \\ } \\  \\ void loop() { \\ //read the analog in value: \\ sensorValue = analogRead(analogInPin);// \\ map it to the range of the analog out: \\ outputValue = map(sensorValue, 0,70, 0, 255); \\ //change the analog out value: \\ analogWrite(analogOutPin, outputValue);// \\  \\ print the results to the Serial Monitor: \\ Serial.print("sensor = "); \\ Serial.print(sensorValue); \\ Serial.print("\t output = "); \\ Serial.println(outputValue); \\  \\ //wait 2 milliseconds before the next loop for the analog-to-digital // \\ converter to settle after the last reading: \\ delay(2); \\ } |
+I Found a setup on the internet to work my DC motor with MOSFET. Because in the internet is recomending to use **PN2222 Transistor . **
+But this transistor working only 200 amper DC motors. My DC motor is using 430 amper.
+{{:fabricademy2017:students:ayseesindurmaz:final_project:1.jpg?nolink&695x411|1.jpg}}
+{{:students:ayseesindurmaz:final_project:img_8989.jpg?nolink&800x600}}
 \\