Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
fabricademy2017:students:anamaria.martinlopez:week11 [2017/12/11 23:01]
anamaria.martinlopez
fabricademy2017:students:anamaria.martinlopez:week11 [2017/12/12 07:33] (current)
anamaria.martinlopez
Line 1: Line 1:
  
  
-**Muñeca neumática ​**+**
  
-En esta clase quería comenzar con el primer ejercicio, nunca he hecho algo similar y quería experimentar desde cero.+Pneumatic Wrist   ​** ​   ** **
  
-Primero hice una prueba rápida con vinilo textil para verificar la resistencia.+In this class I wanted to start with the first exercise, I have never done anything similar and I wanted to experiment from scratch. 
 + 
 +First I did a quick test with textile vinyl, to check the resistance.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo.png?​nolink&​731x250 ​ }} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo.png?​nolink&​731x250 ​ }}
  
-Seguí este tutorial: [[https://​softroboticstoolkit.com/​resources-for-educators/​pneuwrist-brace|https://​softroboticstoolkit.com/​resources-for-educators/​pneuwrist-brace]]+I followed this tutorial: [[https://​softroboticstoolkit.com/​resources-for-educators/​pneuwrist-brace|https://​softroboticstoolkit.com/​resources-for-educators/​pneuwrist-brace]]
  
-Paso 1: abra con Rhinoceros ​y haga una copia espejo para la parte posterior.+Step 1: Open with Rhinoceros ​and make a mirror copy for the back part.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​capturav.jpg?​nolink&​600x293 ​ |capturav.jpg}} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​capturav.jpg?​nolink&​600x293 ​ |capturav.jpg}}
  
-Paso 2:+Step 2:
  
-Material: ​vinilo textil+Material: ​textile vinyl
  
-Corta con el plotter ​y prepara las dos partes quitando los restos que no queremos.+Cut with the plotter ​and prepare the two parts by removing the remains that we do not want.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo1.png?​nolink&​731x250 ​ }} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo1.png?​nolink&​731x250 ​ }}
  
-Paso 3:+Step 3:
  
-Recorte con papel de pergamino sobre el diseño dejando ​1 cm alrededor para sellar la pulsera.+Trim with Parchment paper over the design leaving ​1 cm around to seal the wristband.
  
-Únete a las tres partes.+Join the three parts.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo7.png?​nolink&​780x340 ​ }} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​dibujo7.png?​nolink&​780x340 ​ }}
  
-Etapa 4:+Step 4:
  
-Hierro teniendo en cuenta la temperatura según el vinilono todos se pueden planchar a la misma temperatura ​(mire la temperatura cuando compra viniloen mi caso lo planché a 150 grados durante ​17 segundos.+Iron taking into account the temperature according to the vinyl, not all can be ironed at the same temperature, (look at the temperature when you buy vinylin my case I ironed it at 150 degrees for 17 seconds.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0892.jpg?​nolink&​600x800 ​ |img_0892.jpg}} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0892.jpg?​nolink&​600x800 ​ |img_0892.jpg}}
  
-Paso 5:+Step 5:
  
-Retire la transferencia con cuidado.+Remove the transfer carefully.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0938.jpg?​nolink&​600x800 ​ |img_0938.jpg}} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0938.jpg?​nolink&​600x800 ​ |img_0938.jpg}}
  
-Paso 6:+Step 6:
  
-Introduzca el cordón elástico a través de los agujeros y revise sin dejarlo muy apretado.+Introduce the elastic cord through the holes and check without leaving it very tight.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0941.jpg?​nolink&​600x800 ​ |img_0941.jpg}} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0941.jpg?​nolink&​600x800 ​ |img_0941.jpg}}
  
-Paso 7: Introduzca el tubo y llénelo de aire para verificar que no haya fugas.+Step 7: Introduce the tube and fill it with air to check that there are no leaks.
  
 {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0946.jpg?​nolink&​600x800 ​ |img_0946.jpg}} {{  :​fabricademy2017:​students:​anamaria.martinlopez:​week_8:​week11:​img_0946.jpg?​nolink&​600x800 ​ |img_0946.jpg}}